Downloads:
dap23
Phase detection for three-phase, two-phase, or single-phase systems
Mains frequency: 50 Hz, 60 Hz, and 400 Hz (40 Hz…500 Hz)
Prevents startup in the event of a missing phase.
Protects sensitive equipment from power supply faults.
Use of the neutral wire is optional in three-phase systems
Phase-by-phase status relay output
Contactor control, PLC input
Connecting the relays in series provides a summary relay output
Downloads:
ctl105
Up to 6 measurement channels; probe inputs; voltage outputs: 0–10 V,
Fully configurable: range, filter, offset,
Low-cost applications
The CTL105 is a programmable multi-channel temperature measurement converter designed to process signals from PT100 temperature sensors and convert them int
. It is primarily intended for use in complete system instrumentation, such as motors, heat pumps, and wind turbines.
Downloads:
cssip105
SSi Synchronous Serial Interface Input Master or slave mode
SSi formats from 8 to 25 bits (binary or Gray code) Encoder power supply
Parallel digital outputs (Grey code or binary) (25 bits + enable)
Modbus TCP Ethernet connection option
The CSSIP105 is a serial-to-parallel converter that enables parallel transmission (in binary or Gray code) of an SSi absolute encoder; the display allows for quick diagnostics of proper operation (display of the input signal, the associated physical scale, and the status of the outputs).
Downloads:
crl20
Digital-to-Analog Converter
Converts RS485 Modbus to analog signal
4 isolated analog outputs (4-20mA or 0-10V)
Fully configurable
The CRL20 network converter retrieves variables from a MODBUS network
and converts them into analog signals.
Downloads:
cpl35l
For AC and DC signals
AC + DC RMS measurements: DC to 440 Hz
PWM, phase angle modulation, wave trains, signals with high harmonic content
Multi-sensor current input:
shunt, transformer, Rogowski coil, Hall effect sensor or direct input 1A and 5A
Programmable: voltmeter, ammeter, frequency meter
4-digit measurement display for U, I, Hz
2 isolated analog outputs for simultaneous voltage and current transducers
3 relay outputs
Ethernet connection with Modbus-TCP and SNMP
Wide-range universal AC/DC power supply
The CPL35L is a programmable voltage and current measurement converter. Its various output options—
—enable a wide range of applications, including measurement, protection, and control. The second analog output allows
to simultaneously measure voltage and current in a fully isolated manner.
Downloads:
cpl35
Wattmeter, Voltmeter, Ammeter,
.
AC + DC RMS measurements: 0–440 Hz Single-phase, Two-phase, Balanced three-phase with or without neutral
PWM PWM, Waveform, Phase Angle Variation Signals with high harmonic content
Multi-sensor current input: shunt, transformer, Rogowski coil Hall effect sensor or direct input 1A and 5A
Programmable:
Voltmeter, ammeter, wattmeter, varmeter,
power factor, Cos phi, frequency meter
AC and DC energy meter
4-digit measurement display: U, I, Cos, P, Q, Hz
Outputs: 2 analog outputs, 3 relay outputs,
Ethernet connection Modbus-TCP and SNMP
Wide-range universal AC/DC power supply
The CPL35 is a converter designed for measuring, monitoring, and transmitting electrical parameters. It can be quickly configured by simply programming the transformer ratios or shunt sensitivity
. The various output options enable a wide range of applications: measurement and protection
Downloads:
cpl23
Measurements: voltage, AC and DC current, and frequencies
Fully configurable analog outputs
Continuous and alternating measurement
CPL23L: 1 analog output
CPL23: 2 analog outputs
Response time: <150 ms
The CPL23 is a programmable transmitter designed for electrical network measurements. It is fully user-
-configurable and can be used as a voltmeter, ammeter, or frequency meter.
Downloads:
cpl165
Energy meter for 18 three-phase or single-phase circuits, measures U, I, Cos, P, W
Current measurement from 1A to 500A via Tio mini-transformer with opening mechanism. Passage diameter: 12 to 36mm
Ethernet connection via Modbus TCP or SNMP. Embedded web server
6 simultaneous Modbus TCP connections
Option for direct bus connection on the DIN rail
Modbus connection via RS485 option
Application:
Energy efficiency, building management
Data center: Smart PDU, PUE (Power Usage Effectiveness) measurement
The CPL165 is a comprehensive and highly compact measurement device designed to measure electricity consumption (building management, workshops, data centers, etc.) as part of an energy efficiency initiative. The Ethernet connection enables monitoring of measurements while ensuring quick and easy integration into the existing network. The internal bus allows multiple modules to be connected via a single Ethernet link. The product can be used independently on either a three-phase or single-phase network.
Downloads:
cpl105
Three-phase or single-phase network, measurement of U, I, Cos, P, Q, W
Multi-sensor: Ti, Rogowski coil
Ethernet connection: Modbus TCP or SNMP Embedded web server
6 simultaneous Modbus TCP connections
Option for direct bus connection on the DIN rail
RS485 Modbus connection
3 relay outputs
Display: 2-line LCD with 16 characters per line
Can be used as 3 isolated single-phase meters
The CPL105 is primarily designed for power and energy measurement in electrical management applications
(building and workshop management, etc.), and the Ethernet connection allows for monitoring of measurements while
ensuring quick and easy integration into the existing network. The internal bus allows multiple modules to be consolidated onto a single Ethernet connection.
Downloads:
cpl101
Electrical Measurement Transmitter Unbalanced three-phase network with or without neutral, frequency from 40 to 400 Hz.
Programmable: functions: voltmeter, ammeter, frequency meter, wattmeter, varmeter, power factor, power factor (Cos phi)
Up to 3 analog outputs: 0…4…20 mA, 0…10V, +/- 20mA, +/-10V
1 relay output usable for energy metering or as a threshold relay
CPL101/C: RS485 MODBUS connection option
CPL101T: High-speed version (response: 100 ms)
The CPL101 is a programmable transmitter designed to measure electrical network parameters.
It supports all network wiring configurations commonly found in industry. Equipped with a wide range
of outputs, it can be used as an analyzer, converter, energy meter, controller, or protective device.