Downloads:
temax105
Temperature input: Up to 4 platinum sensors
2-wire technical output (powered by the 4–20 mA loop)
Display of maximum, minimum, or average temperature
Display: 2-line, 16-character LCD
Simultaneous display of 4 temperatures
Fully customizable
The TEMAX105 LCD is a programmable 2-wire digital converter with an LCD display (
) designed to process signals from PT100 temperature sensors (maximum value, minimum value, average value).
Downloads:
inp201
LCD display: 10,000-point configurable display range
2-wire technology, loop-powered 4–20 mA
Mounting: support tube or pyrometric rod, IP65 protection
INP201i 316 stainless steel housing version
INP201H HART protocol option
INP201ADF ATEX / IECEx explosion-proof option
SIL2 compliance according to IEC 61508
Stainless steel version
The INP201 is a loop-powered field transmitter-indicator 4
.20mA loop-powered transmitter-indicator.
It combines in a single housing (IP65) (ATEX-certified explosion-proof) a 2-wire converter
as well as a configurable loop indicator.
Downloads:
inp101
2-wire technology (isolated 4–20 mA)
INP101V on a rod INP101 on a pyrometric rod
INP101i stainless steel version
Local display: 10,000 points
Outdoor installation, IP67 protection rating
Explosion-proof protection ATEX and IECEx certified
INP101V: adjustable internal display for vertical or horizontal mounting
INP101i: 316 stainless steel housing version
HART protocol
FDT-certified HART DTM drivers
SIL2 compliance according to IEC 61508
The INP101 is a self-powered field transmitter and indicator that draws power from the 4–20 mA loop.
It combines a programmable converter
(CNL40IG in 2-wire configuration) and a 4-digit digital display in a single housing designed to withstand harsh environments (IP 67).
Downloads:
dnl35-mli
Process inputs (Volt, mA, sensor power supply, potentiometer)
2, 3, or 4 relay outputs (programmable PWM output)
Measurement display (10,000 points); programming via front panel and RS232
Universal power supply
Short cycle time: 20 ms
The DNL35-MLi converts an analog signal into potential-free contact outputs
that are pulse-width modulated (with a duty cycle proportional to the input signal)
The transfer function (slope, offset, and dead zone) can be freely configured to suit the application.
Downloads:
ctl105
Up to 6 measurement channels; probe inputs; voltage outputs: 0–10 V,
Fully configurable: range, filter, offset,
Low-cost applications
The CTL105 is a programmable multi-channel temperature measurement converter designed to process signals from PT100 temperature sensors and convert them int
. It is primarily intended for use in complete system instrumentation, such as motors, heat pumps, and wind turbines.
Downloads:
cssip105
SSi Synchronous Serial Interface Input Master or slave mode
SSi formats from 8 to 25 bits (binary or Gray code) Encoder power supply
Parallel digital outputs (Grey code or binary) (25 bits + enable)
Modbus TCP Ethernet connection option
The CSSIP105 is a serial-to-parallel converter that enables parallel transmission (in binary or Gray code) of an SSi absolute encoder; the display allows for quick diagnostics of proper operation (display of the input signal, the associated physical scale, and the status of the outputs).
Downloads:
cnlb20pot
All types of voltage, current, and temperature inputs: 4..20mA, 0..10V, Pt100, Thermocouple
.
Fully configurable
2-wire or 3-wire resistive output 256 conversion steps
Transfer function adaptable via 51-point linearization
Fully isolated
Plug-in connector
The CNLB20pot converts an analog signal (4–20 mA; 0–10 V, or other) into a variable resistance or potentiometer
Downloads:
cnl70
Temperature and process inputs: Platinum sensor, thermocouple, mV, mA, potentiometer
2-wire output powered by the 4-20mA loop
Input/output galvanic isolation
4-digit LCD display, 10,000 counts
Fully configurable RS232 and HART
CNL70-H HART Protocol FDT-certified HART DTM drivers
SIL2 compliance according to IEC 61508
The CNL70 is a programmable digital signal conditioner powered by a 4–20 mA current loop (
) with an LCD display, designed for measuring temperature sensors (thermocouples and PT100s) as well as process signals (mV, mA). Optionally, it can include Hart protocol communication and meet the SIL2 safety integrity level (
) in accordance with IEC 61508.
Downloads:
cnl45d
Process and temperature inputs: voltage (V), mV, current (mA), potentiometer, thermocouple, PT100
2-wire technology powered by the 4-20 mA loop
Galvanic isolation
Fully configurable
Measurement display (10,000 points)
High thermal stability
The CNL45D is an isolated digital transmitter powered by a 4–20 mA loop, combining the ease of
implementation of two-wire technology with the flexibility of configurable converters.
Downloads:
cnl45
Programmable process and temperature inputs: Volts, mV, mA, potentiometer, thermocouple, PT100
2-wire configuration powered by the 4-20mA loop
1000V input/output galvanic isolation
Fully configurable RS232 interface
High thermal stability 50 ppm
The CNL45 is an isolated digital transmitter powered by the 4-20mA loop, combining the ease of implementation of
two-wire technology with the flexibility of configurable converters.